Fumonisins fluorescence quantitative rapid test card

Catalog No.: IF005A01

[Brief]

This product is used for rapid quantitative detection of Fumonisins in grains and their products, feed raw materials, and some finished feed products. It is suitable for on-site rapid detection by various enterprises, grain depots, testing institutions, and government regulatory departments.

 

[Principle]

This product is based on the principle of competition and combined with fluorescence chromatography technology. The Fumonisins (FUM) in the sample competes with the FUM-Ag coated on the NC membrane testing line for fluorescent microsphere labeled FUM monoclonal antibody. As the FUM content in the test sample increases, the amount of fluorescent microsphere antibody complex bound to the testing line decreases, and the fluorescence intensity of the testing line weakens accordingly. After the reaction is completed, the content of FUM in the sample can be detected using a matching handheld fluorescence immunoassay analyzer.

 

[Application]

Grains and their products, feed raw materials, and some finished feed products.

 

[Specification]

20 tests/box; 50 tests/box

 

[Product performance]

Detection range: 0～12000μg/kg(ppb)

Detection limit: 250μg/kg(ppb)

Recovery rate: 80%～120%

 

[Components]

 

[Required equipment, consumables, and reagents] (Not provided)

1. Equipment and consumables: electronic balance, oscillator, centrifuge, pipette, and tips (20-200μL,100-1000μL, 1-5mL), centrifuge tube (50mL, 1.5mL), disposable gloves and mask.

2. Reagent: Anhydrous ethanol (AR).

 

[Reagent preparation]

Sample extraction solution: Take 500mL of anhydrous ethanol and add 500mL of pure water, mix well for usage.

 

[Experimental Steps]

1. Preparation before testing

a. Return the test card and sample diluent to room temperature (25℃) for at least 30 minutes.

b. Turn on the power of the fluorescence immunoassay analyzer, preheat for 10 minutes.

c. Turn on the constant temperature timer, set the incubation temperature to 37 ℃ and the incubation time to 8 minutes.

 

2. Sample preparation

Multiple point sampling is required for the test sample, with a total sampling amount of 300-500g. After thorough mixing, the particles can be homogenized to over 90% and pass through a 20 mesh sieve. Extract the screened samples for testing.

a. Conventional samples

Weigh 5.0±0.05g of homogeneous sieved sample into a 50mL centrifuge tube, add 25mL of sample extraction solution, shake for 3 minutes, and centrifuge at 4000rpm for 5 minutes. Take 50μL supernatant, add 750μL sample diluent, shake and mix well for 10 seconds, ready for testing.

b. Bran sample (strong water absorbing sample)

Weigh 2.5±0.025g of homogeneous sieved sample into a 50mL centrifuge tube, add 25mL of sample extraction solution, shake for 3 minutes, and centrifuge at 4000rpm for 5 minutes. Take 50μL supernatant, add 750μL sample diluent, shake and mix well for 10 seconds, ready for testing. (In this case, multiplying the test result by 2 is the final concentration)

Note: When the concentration of the analyte in the sample exceeds the range of the curve, the sample extraction solution can be used to dilute the extracted supernatant by 2-5 times, then take 50μL diluted extraction solution, add 750μL sample diluent, mix thoroughly and add the sample for testing. The final result is obtained by multiplying dilution factor.

 

3. Sample testing

a. Take out the warmed test card from the aluminum foil bag, place it on a horizontal table, and use a pipette to aspirate 70μL of the diluted sample, add into the sample hole, insert the test card into the constant temperature timer socket, and incubate for 8 minutes;

b. Insert the ID card of the corresponding project and batch into the fluorescence immunoassay analyzer and read the ID card information;

c. After incubation, select the sample type (standard curve) corresponding to the test sample, insert the test card into the fluorescence immunoassay analyzer (see the manual of analyzer for specific operation), and click "Test" to perform the testing.

Note: During testing, do not point the constant temperature timer socket towards the air conditioner or fan vent.

Sample type corresponding to sample kind (standard curve)

Sample kind (standard curve)	Applicable sample types
Sample kind 1	Samples and processed products of grains such as wheat, corn, rice, peanuts, and beans, as well as feed raw materials and some finished feed products

4. Result acquisition

The test results will be displayed on the screen of the fluorescence immunoassay analyzer. You can click to print to obtain a paper printed report, or export an electronic version of the data report through a data cable.

 

[Precautions]

1. Please use the test card within its validity period, and each card can only be used once;

2. Please use the test card immediately when opening the aluminum foil bag packaging;

3. Different batches of test cards, sample diluents, and ID cards should not be mixed;

4. Do not touch the white film strip at the detection window. If touched, please discard this card to avoid affecting the detection results;

5. Please test immediately after incubation and try to complete the test within 2 minutes after incubation;

6. During the testing process, reagents, instruments, etc. should be avoided from direct sunlight, fans, and air conditioning;

7. This product is only used for screening. If a positive result appears, it is recommended to use national standard methods for confirmation;

8. If you encounter any problems during testing, please contact the supplier.

9. The disposal of experimental waste shall be carried out in accordance with national or local laws and regulations.

 

[Storage and shelf life]

1. This product should be stored in a dry and dark place at 2-8 ℃, and should not be frozen.

2. The shelf life is 12 months. The batch number and production date can be found in the outer packaging.

 

Shenzhen Lvshiyuan Biotechnology Co., Ltd

D Building, National Biological Industrial Park of Marinelife, No.2 Binhai Road, Dapeng, Shenzhen, 518120 China

Tel. 86-755-28438788     

Fax 86-755-28938800

Email: info@lsybt.com      

Website: www.lsybt.com